up and running but....
-
also, get rid of the values you have in the solo mining section. I'm not sure if they'll help, but they may confuse the program since you can't solo and pool mine at the same time with jminer.
Cheers!
-
well one other issue i only just discovered... it does not generate any files in the plot directory
-
@vmantilla said in up and running but....:
optDevPool=false
that one is not there at all... ie i searched for optDevPool and DevPool
-
Added the statement under the wallet server section. Like this.
walletServer=
winnerRetriesOnAsync=
winnerRetryIntervalInMs=optDevPool=false
The jminer I downloaded had this optDevPool statement, and when I set it to false, jminer worked when it previously had not.
-
-
No plots yet? jminer will not plot. You need xplotter for this. Takes a while to get a drive completely plotted, so take a seat and get some cold drinks.
The AIO wallet will run xplotter for you, if you want to. There is some teenie text (4- 6 pt font or less) in the bottom left margin that reads "Write Plots". Click on this, then select your drive. It should star right up, writing optimized plots.
Like I said, it takes a while to get the whole drive plotted. However, you can start mining as soon as xplotter gets going. You may not have a lot of DLs, though, until some reasonable portion of your drive is plotted.
-
ahh.... i thought jminer would also do some plotting :-D
i guess this explains this:
2017-06-23 22:40:11.055 INFO 6556 --- [ roundPool-1] burstcoin.jminer.JMinerCommandLine : START block '374306', scoopNumber '3458', capacity '0 GB'
2017-06-23 22:40:11.056 INFO 6556 --- [ roundPool-1] burstcoin.jminer.JMinerCommandLine : targetDeadline '2592000', baseTarget '448546'ie 0 GB
-
even if i use the AIO to run xplotter and move the plot file to the path set in jminer config it does still say the same... hmmm
i tried to make it list the plot files and it did not list any....
-
plotPaths=C:\Jminer\plots2
scanPathsEveryRound=true
listPlotFiles=true
-
@boelle change your plotPaths statement, should be: plotPaths=c:/jminer/plots2
-
tried that too
i even switched to jminer 0.4.8
-
2017-06-23 23:07:41.333 INFO 4312 --- [ roundPool-1] burstcoin.jminer.JMinerCommandLine : START block '374313', scoopNumber '98', capacity '0 GB'
2017-06-23 23:07:41.333 INFO 4312 --- [ roundPool-1] burstcoin.jminer.JMinerCommandLine : targetDeadline '2592000', baseTarget '402867'also it does not list the plot files as i have told it to
-
dooooh..... haitch pointed out that i have used the wrong num account... not sure how i screwed that up
jminer is now running
now are there downsides to use small plots of say 2gb compared to 52gb ones?
-
Those are both really small.
That being said, bigger is better. Not really sure what kind of results you'll get with a 52gb plot. It may be too small.
-
i come from the distributed computing world where its perfecty ok to use small blocks of work as long you have a permanent connection to internet
it will just fetch work more often
-
btw.... can jminer be configured for more than one device?
currently i have it set for GPU but what about both GPU and CPU.. ie at night when sleeping
-
I do not know. I think jminer uses your GPU. You can use your CPU for plotting, but not jminer. You can plot with xplotter.
I hope this helps.
